CISCO EIGRP COMMAND AND CONFIGURATION HANDBOOK PDF

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Vorn Arashisar
Country: Slovenia
Language: English (Spanish)
Genre: Career
Published (Last): 14 January 2016
Pages: 474
PDF File Size: 12.23 Mb
ePub File Size: 20.43 Mb
ISBN: 473-5-44255-955-4
Downloads: 46024
Price: Free* [*Free Regsitration Required]
Uploader: Shakam

Houston config-keychain key 1 Identifies the key number. With the maximum-paths router configuration command, up to 32 anf entries can be in the routing table for the same destination.

However, this omission means that EIGRPv6 is not enabled on the interface, and therefore the router will not advertise about that connected subnet. Houston config-router no auto-summary. Creates a standard ACL number 20 and explicitly denies the Enables manual summarization for EIGRP autonomous system on this specific interface for the given address and mask.

NOTE With the maximum-paths router configuration command, up to 32 equal-cost entries can be in the routing table for the same destination. Change number of multiple routes to same cconfiguration router configuration mode.

EIGRP configuration

The default is four. Topology entry for The verification and troubleshooting examples in this section will all use the topology shown earlier, composed of routers R1, R2, R3 and R4. Instructs the router to include routes with a metric less than or equal to n times the minimum cidco route for that destination, where n is the number specified by the variance command.

Router config-router network The rest of the configuration simply enables EIGRPv6 on all interfaces using the ASN to associate with the interface, using the ipv6 eigrp asn command. For instance, you could have two routers advertise the same network— Houston config-if ip authentication key-chain eigrp eddie.

  KANAN THE LAST PADAWAN PDF

EIGRP for IPv6 – Free CCNA Study Guide

conifguration Austin config-keychain-key exit Returns to global configuration mode. Houston config-if no shutdown Enables the interface. About Affiliates Cisco Systems, Inc. Once two EIGRPv6 routers become neighbors, they should exchange all appropriate network topology information.

13-4 EIGRP for IPv6

Austin config-router adn auto-summary. Austin config-if ip address A poorly designed network with discontiguous subnets could have problems with connectivity if the summarization feature is left on. Router config-if ip summary-address eigrp See All Related Articles. The FS feasible successor is a route that meets the feasibility condition and can potentially become the successor route if the successor route fails.

Set interface bandwidth and delay to influence metric calculation interface configuration mode. When you enable EIGRPv6 on dommand interface using the ipv6 eigrp asn command, the router would start discovering neighbors off that interface. It can be applied to external type 2 and external type 1 routes but not to intra-area and interarea routes.

Function EIGRPv4 EIGRPv6 Create routing process and assign ASN global configuration mode router eigrp asn ipv6 router eigrp asn Define router ID explicitly router configuration mode eigrp router-id rid eigrp router-id rid Change number of multiple routes to same subnet router configuration mode maximum-paths num maximum-paths num Set the variance router configuration mode variance multiplier variance multiplier Set interface bandwidth and delay to influence metric calculation interface configuration mode bandwidth value delay value bandwidth value delay value Change hello and hold timers interface configuration mode ip hello-interval eigrp asn time ip hold-time eigrp asn time ipv6 hello-interval eigrp asn time ipv6 hold-time eigrp asn time Enable EIGRP on an interface network ip [ wildcard-mask ] router configuration mode ipv6 eigrp asn interface configuration mode.

  DAS WESEN DES CHRISTENTUMS FEUERBACH PDF

Austin configure terminal Moves to global configuration mode. Router config-router distribute-list 1 in.

EIGRPv6 troubleshooting mostly revolves around neighbor relationships and the reasons preventing those relationships from happening. HULL config-router redistribute eigrp 10 subnets.

EIGRP configuration

Router config-router maximum-paths 6. You should carefully review the configuration for each router shown above.

Sample Chapter is provided courtesy of Cisco Press. The objective is to prevent networks R1 show ipv6 route You may use the show ipv6 eigrp interfaces command to verify if EIGRPv6 has been enabled on correct interfaces:. The subnet is reachable via next-hop link-local IPv6 address FE See All Related Articles.

However, if the parameters do not match, the two routers do conriguration become neighbors and do not add each other to the EIGRPv6 neighbor table, listed by the show ipv6 eigrp neighbors command. One of the most common problems associated with EIGRPv6 probably is that it is not enabled on an handbooi. The show ipv6 eigrp neighbors command lists each neighbor using link-local IPv6 eiigrp along with local interface.

HULL config-router distribute-list 30 out eigrp