ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.
|Published (Last):||5 June 2010|
|PDF File Size:||4.20 Mb|
|ePub File Size:||1.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A787 Carbon Steel Tubing Manufacturer in India
It is informational only and not an official part of the standard; the full text of the standard itself ast be referred to for its use and application. Within the text, the SI units are shown in brackets. ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
The steels shall conform to elemental tolerances for product analysis. Low-carbon steels and other carbon steels shall conform to the required chemical composition for carbon, manganese, phosphorus, and sulfur. A Type 6 Tubing asgm a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes. Sizes outside the ranges listed above may be ordered provided all other requirements of the specification are met.
This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized after welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet. Referenced Documents purchase separately The documents aastm below are referenced within the subject standard but are not provided as part of the standard.
ASTM A Type 3 welded mechanical tubing is produced out of a hot rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing asstm already formed and welded. Combining values from the two systems may result in non-conformance with the standard. This abstract is a brief summary of the referenced standard.
ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel
Link to Active This link will always route to the current Active version of the standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon atm while in coil form.
This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation SI unitsthe inch-pound units shall apply. Combining values from the two systems may result in non-conformance with the standard. Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided.
A Mechanical Tubing | Alro Steel
ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form and then heat treated to convert the coating into a zinc-iron alloy. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Historical Version s – view previous versions of standard.
The values stated in either SI units or a78 units are to be regarded separately as standard. Outside Diameter Tange, in. Carbon Steel A Tube Exporter. Within the text, the SI units are shown in brackets.
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.